If you have a lot of laundry to take care of, a dirty iron can cause problems.Water can leave behind mineral deposits over time.If you use a spray on a product, it can leave gunk on the plate of the iron.irons are easy to clean if you do it on a regular basis
Step 1: White vinegar and salt are mixed.
The mixture will be heated on the stove.Don't let the vinegar come to a boil, but heat until the salt is dissolved.It will be a good cleaner for the iron because of the strong smell.
Step 2: Allow the mixture to cool.
Leave the hot liquid to cool down.You want it to be warm, but not hot.It's a good idea to wear dish gloves to protect your hands.
Step 3: A rag should be put into the mixture.
Rub the cooled mixture on the bottom of the iron to clean the plate.Unless you have a teflon coated iron, you can use a soft brush to do this.The iron's plate will be ruined if you use a wire brush.It's a great way to get rid of marks on the iron.
Step 4: The iron should be washed.
After you are done cleaning, you should remove any leftover bits from the mixture.You can wash the plate of the iron by dipping a clean rag in some white vinegar.You can run the iron over the clean cloth after turning it on.It will help to burn off any leftover material.
Step 5: Make a paste.
A paste of water and baking soda is needed.The paste should be thick enough to stick to the plate of your iron.If you can, use a distilled water.
Step 6: After the iron has cooled, spread the paste on the plate.
Before you use the iron, make sure the plate is completely cool.The paste can be applied directly to the plate.If your iron is only dirty in one place, you don't have to spread it all over.It is a good idea to spread the paste over the entire plate if you are just doing a general cleaning.You can either use a spatula or your fingers.If there is a lot of iron build up, you can leave this paste on the iron for a few minutes.If your iron is dirty, spread the paste generously.
Step 7: Get a clean cloth.
Make sure the paste is clean before you use this.Get the cloth wet.Put out any excess water and then wipe the paste off the iron.
Step 8: The steam holes need to be cleaned.
People use a cotton swab to clean their ears.The cotton swab can be used to clean the steam holes.If there is a lot of gunk coming out of the holes, you may need to use more than one cotton swab.If there is a lot of build up on the cotton swab, use a new one.
Step 9: The reservoir should be filled.
If there is any water left in the iron, be sure to empty it first.If you open the hatch and turn it upside down, you can do this.After it's empty, use distilled or filters and fill about 1/3 of the way.A stronger cleaning solution can be found in the mixture of water and white vinegar.You should read your iron's instruction manual to make sure that it will tolerate the substance.
Step 10: The iron needs to be turned on.
Make sure the steam setting is on when you turn the iron to its highest setting.The steam and heat will remove gunk and mineral deposits from the steam holes.When working with a hot iron, be careful.Don't get burned by the steam that comes from the iron.
Step 11: For a few minutes, iron a clean cloth.
If you don't mind getting dirty, choose a clean cloth.There are brown streaks on your cloth if there is dirt inside the iron.To clean the iron, you need to iron the cloth.Press the button often if you have a manual steam button.A towel is likely to work for this.
Step 12: Let the iron cool down.
You should place the iron on a protected surface.The counter is covered with a towel.The iron might get old as it cools down.If there is any leftover water, be sure to remove it.
Step 13: Rub the iron plate with a new dryer sheet.
Your iron should be turned on the lowest setting.Rub the iron plate on the dryer sheet until all of the dirt and gunk is gone.When you are done, iron a clean rag and turn on the heat of the iron to get rid of any leftover lint.
Step 14: The iron's reservoir needs to be filled.
If it is available to you, you should use it.For five minutes, iron a thick piece of cotton cloth with the iron.The soleplate needs to be cleaned with a clean towel.It is important to check your owner's manual to make sure that your iron can tolerate vinegar.
Step 15: Use toothpaste to clean the soleplate.
It's important to hit trouble areas with a bit of toothpaste on a cool soleplate.Set the iron on steam and steam a cloth for five minutes, then rub the toothpaste off with a clean cloth.You can mix together toothpaste, baking soda, and vinegar and use it to clean the soleplate.
Step 16: The iron needs to be cleaned with newspaper.
Turn the heat on the iron all the way up and turn off the steam if there is a sticky bottom.If you want to keep the newspaper clean, run the hot iron over it.Sprinkle a bit of salt on the newspaper if it is still sticky after this.It should take care of sticky substances.