There are many ways to clean concrete steps.If you want to clean your concrete steps, you can use a mild dish soap and a stiff bristle brush.To clean concrete steps thoroughly, use a concrete cleaner with a push broom or a pressure washer.
Step 1: The steps need to be swept.
The concrete steps have dirt and debris on them.If you want the steps to be free of dirt and debris, you need to sweep them.The concrete will be prepared for the cleaning process.You can use a leaf blower to clean the steps.
Step 2: The hot water and dish soap should be mixed together.
Liquid dish soap can be used.In a plastic bucket, mix the ingredients together.In order to make the solution more potent, mix in one part vinegar.The water should be at least 105 degrees.
Step 3: Put the solution over the stains.
Make sure the solution completely covers the stain.The solution will be set for 10 to 15 minutes.Make sure the solution doesn't dry while it's setting.Pour more solution onto the stain if it begins to dry.You may need to let the solution set for 30 minutes if the stain is old or stubborn.
Step 4: The stain should be scrubbed with a stiff bristle brush.
Don't use a metal scrub brush.Wait until the stains are completely removed to scrub them.Sprinkle laundry detergent on the stains if they remain.The detergent needs to be set for 10 to 15 minutes.After the allotted time, pour hot water onto the stains and scrub them with your stiff bristle brush.
Step 5: It's best to rinse with hot water.
The steps should be washed with hot water until all of the soap is gone.The water should have a temperature of at least 105 degrees.
Step 6: The steps have debris on them.
The concrete steps have a lot of dirt and debris.It's a good idea to cover up any nearby plants with a plastic covering.Take away toys, decorations, and furniture.
Step 7: One part hot water and one part bleach.
They should be mixed in a plastic bucket.The water should have a temperature of at least 105 degrees.Alternatively, you can use a specially formulated concrete cleaner instead of the oxygenated bleach and water.These can be found at your local hardware store.
Step 8: The steps should be sprayed with solution.
Put the solution in a tank sprayer.From the top down, spray the steps with the solution to focus on the stained areas.The solution should be set for 20 to 30 minutes once you have covered the whole area.Make sure the steps are wet to prevent the solution from drying up.Just spray more solution onto the steps if the solution starts to dry.You can buy or rent a tank sprayer at your local hardware store.
Step 9: The steps have a brush on them.
The push broom can be used to do this.From the top down, scrub the steps until they are clean.To clean small crevices and corners, use a smaller scrub brush.To avoid a patchy look, clean the steps evenly.
Step 10: The steps need to be washed with hot water.
Put hot water in a gallon bucket.The water should be poured down the steps from the top of the stairs.All of the soap, dirt, and grime have to be removed before the steps can be washed.If the concrete steps are still dirty, use a different method or repeat steps one through five.
Step 11: A pressure washer is available for rent.
A pressure washer can be rented from a hardware store.A pressure washer can be rented with a flow rate of at least 4 gallons per minute.
Step 12: There is clear debris away from the steps.
Dirt, leaves, twigs, and other debris can be removed with a broom or electric blower.It's a good idea to remove plants, toys, furniture, and decorations.Plants that can't be removed with a tarp or trash bags should be covered.
Step 13: The steps need to be pre-treated.
A bucket is filled with hot water and liquid dish soap.Once they are well-combined, mix the ingredients together.Use a push broom or a stiff bristle brush to scrub the concrete.The solution should be set for 15 to 20 minutes.You can treat the steps with a concrete cleaner.
Step 14: The steps need to be washed.
The pressure washer should be connected to the instructions in the manual.The high-pressure nozzle can be used to clean the steps.The nozzle should be facing the concrete.Start at the top of the steps and sweep them in a back and forth motion.Remove the soap, dirt, and grime from the steps.To ensure your safety, wear close-toed shoes, clothing that can get wet, and safety goggles.
Step 15: The steps need to be dry.
Once the steps are clean, do this.Make sure the concrete is completely dry before you apply a sealant.It may take a couple of days for the concrete to dry completely.