How to install a sink in a house with plumbing.
When it comes to bathroom sinks, you always deal with wall plumbing.It's obvious that wall plumbing means a Vanity and more storage space.If you are like me, you like the look of a single sink.
The need to cut into the wall is eliminated by floor plumbing.The extra work will be worth it if you have just renovated your bathroom or live in an old building.
If you find yourself in a situation where your bathroom has a floor drain instead of a wall drain, floor plumbing is the only viable option.
We will show you how to plumb a sink through the steps without using the S-traps.
You will need the following things if you want to mount a sink to the floor.
Both hot and cold water can be supplied to your bathroom sink.Turn off both and let the water run out.
You should put a bucket underneath the P-trap because you are going to remove it next.
The P-trap is fastened to the rest of the structure with a slip nut.The P-trap can be removed.Let the water go into the bucket.
Pull the bucket under the water lines.Let the water go into the bucket.
If you don't have a sink attached to the wall on screws, then your job is easier.
If the sink is loosened from the wall, prop it up.The sink can be removed with the help of the wrench.
You will have to pry the sink loose from the Vanity if you have it.If you want to keep the sink for later, you can use a rubber mallet to get it loose.
The height and width of your new pedestal will be determined by these measurements.Once you have taken all of the measurements, it is time to put your fancy piece of furniture to use.
I mean to assemble.You can assess the height and width of the pedestal sink before it is permanently fixed if you see how it looks when all the pieces are together.
The pop-up drain's tailpiece is the height of the P-trap.If there is a mix-up in heights, you may need to cut up the tailpiece.
It is easy to connect the traps to the waste pipe when the sink is installed.
The manual will clearly state whether or not the sink requires extra support.First, read it.
The mounting board is inside the wall.The central line is marked.The sink should be flush against the mounting board if it is center on the wall.
You need to double check the level and get someone to hold the sink for you so that no accidents happen.
To mark the two anchor holes of the sink on the wall, you need to be sure that it is positioned correctly.
If you mark the hole where the pedestal is to be attached to the floor, all three holes can be drilled together.
You should keep in mind that the bolts you use should be at least an inch into the bathroom.Even though the sink is going to be on a pedestal, you will hang it here.
Confused?If the sink is not attached to the wall, it can't stay on the pedestal.The bathroom has a mounting board.
Instead of using a drill, you can attach a cap nut and use a wrench to drive the bolts into the wall.Make sure that an inch of their length is outside the wall.
You can fix the faucet and sink drain here.You do this for the drain.
The same thing is done for the taps.There are several holes on the sink's lip where the faucet is supposed to go, so you need to know this.
Now that the sink is ready, it is time to put it on the bolts.Use washers and cap nuts to secure it.Don't tighten it too much because the sink cracks.
After attaching the P-trap assembly, let's connect the water supply lines.This is what you do.
Take the pedestal underneath the sink and put it in the hole.If you have to raise the sink, do it.Through the bolt hole that was made, screw the pedestal to the floor.
Check to see if the sink is level.The cap nuts need to be tightened.
The most difficult part of plumbing a pedestal sink is running the tailpiece from the drain to the P-trap.
It is important to run the drain correctly.The best part about pedestal sinks is that they don't ruin the vibe of your bathroom with ugly exposed pipes.
Hope that helps you figure out how to fix your sink.Good luck with your plumbing venture, thanks for reading along.