You can make a fake lip stud if you have the right materials.Special glue can be used to create the illusion of a real lip stud for a variety of reasons.
Step 1: There are flatback rhinestones.
The skin under your lip is flat, so rounded-back rhinestones won't stick as well if you have a flatback.This makes it possible for the rhinestones to be on your skin.You should not limit yourself to the beauty store.You can find an endless supply of rhinestones at your local craft store.
Step 2: Pick out your size and color.
It is best to purchase a variety pack.Before committing to one, you can test several sizes on your face.A 5mm diamond may seem like a good choice, but it may be too large for your face.It's possible to get a 2.5mm or 3mm rhinestone.This is comparable to some real lip studs in size.
Step 3: It's a good idea to play with the location.
Use a semi permanent marker to mark the location of your fake lip stud.Do you prefer the middle, side, both sides, or bottom lip?If you want both sides of your lip to have a fake stud, place a strip of tape below your face.Even marking is ensured by this.
Step 4: Get a tool to remove glue.
If you have used spirit gum as a glue, your skin may be tacky and gross.Pick up a spirit gum removal.The glue will be washed away if the remover is used.
Step 5: You need to wash your face.
You want to start with something clean.Don't apply anything to the area where you will apply your lip stud.You can wash your face and towel it off.
Step 6: Use tweezers to remove the back of the rhinestone.
You might want to get a second pair of tweezers.You can use the second pair to remove the protective backing of the rhinestone if you hold it down with one pair.
Step 7: Hold on to your face.
Pick the area you want your fake lip stud to be applied to.The longer your fake lip stud is held in place, the longer it will last.
Step 8: There is a small amount of spirit gum on your face.
When applied to your face, spirit gum will work well.Drug stores may have spirit gum during Halloween.For the rest of the year, check out your local costume shop or online website.
Step 9: The gum should be tacky.
The back of the lip stud will get a proper hold on the gum if it becomes tacky.Test the gum with your finger.It should feel tacky.It is better for the spirit gum to be too dry when in doubt.Don't use a blow dryer or heat form to help the gum tack up faster.
Step 10: Press the piece of jewelry onto your face.
To move a tiny piece of jewelry, use the tweezers.Stick it to your skin with one fluid motion.Do not move it after it has stuck.
Step 11: Hold the piece of jewelry firmly.
Press the piece of jewelry against your face.For approximately ten seconds, maintain.The fake lip stud should be ready to go after ten seconds.
Step 12: Glue the piece of jewelry to it's body.
You can test it by squeezing a single drop onto a piece of tissue.If the drop is larger than needed, use a toothpick to pick up the glue and apply it to the back of the rhinestone.If the test drop is not enough, apply a second drop to the back of the rhinestone.Before applying glue to the bottom of the rhinestone, lift it up and face it.If you spill too much glue on it, it will ruin it.If you don't sweat, eyelash glue is a great glue.It is cheap at most drugstores.
Step 13: Allow the glue to dry for at least 45 seconds.
It is better to let the glue dry longer.It's not enough for the packaging of eyelash glue to say to wait 20 seconds.Glue bonds better to your face when you wait longer.
Step 14: Hold the rhinestone over your face.
Roll your lip back over your teeth to give your face an even canvas.If the flesh on your face is taut, you will have better control over the application of the rhinestone.