A beautiful table runner can make your table arrangements stand out.You can choose your own fabric, colors, sizes, and decorative elements if you learn how to make a runner.Start by sewing a rectangular table runner.Every time, you'll have unique table runners.
Step 1: Determine how long and wide the runner should be.
If you want the runner to hang over the ends of the table, you have to decide which table to use.If you want to see how big the runner is, place a measuring tape across the table.You can add 1 inch to the length and width numbers by writing down your measurements.You'd write down 25 by 97 inches (0.64 m 2.46 m) if you wanted a runner of 2 by 8 feet.
Step 2: Measure your fabric with a fabric pencil.
Take your choice of fabric and spread it on a work surface.Measure with a fabric pencil.You can use any type of fabric.The runner will lay flat if the fabrics are heavier.There is a fabric pencil in the washing machine.
Step 3: Use a sharp pair of shears.
You have to cut along the lines you marked on the fabric in order to make equal pieces.If you want the edges to be smooth, try to cut in smooth lines.Place a cutting mat under the fabric and use a cutter to cut it.
Step 4: Put the pieces in place by stacking the fabric.
If you want the right side of the fabric to face you, make sure the wrong side is facing you.Attach sewing pins to the edges of the fabric.The sewing pins should be about 5 to 6 inches apart.
Step 5: To sew around the edges of a runner, use a straight stitch.
As you sew from the first pin all the way around the runner, leave a 4 inch seam allowance.When you get to the last pin, stop sewing.The gap will be big enough for your hand to fit through.The corners need to be pushed out when you turn the fabric right side out.
Step 6: The excess fabric should be trimmed from each corner.
You can trim the excess point from each corner by using your scissors.Make sure you don't cut across your stitches.Excess bulk can be eliminated by trimming the corners.
Step 7: Push each corner out of the runner's way.
You can grab the fabric by reaching your hand into the gap on the side of the runner.Pull the runner out of the way.Take a sharp object, such as a knitting needle or a chopstick, and push it into the runner.You might damage your stitches if you push too hard.
Step 8: The gap is closed using a sewing machine.
Attach the unfinished hem of the runner to the machine with a straight stitch.Straight Stitch around the perimeter if you want an extra durable runner.Leave a 4 inch (0.64 cm) seam allowance if you stitch around the perimeter 1 more time.
Step 9: You should iron the runner before putting it on the table.
You should read the care instructions for the fabric you used to make your iron.Put the runner on the ironing board and press the iron to flatten it.Learn the care instructions for the fabric so you know how to wash and dry the table runner.
Step 10: A patchwork runner can be made using quilting squares or remnants.
If you like the look of a quilt, sew squares or fabric scraps onto a piece of batting.The batting should be the size you want the runner to be.hem the edges after sewing the fabric onto the batting.The patchwork runner can be complicated or simple.There's less to sew if you keep your squares large.
Step 11: You should cut the ends of the runner to make points.
If you want your fabric pieces to come to triangular points, trim both ends before you finish the edges.Attach a pom pom to the end of each point.
Step 12: Attach the tassels to the pointed ends.
Thin cords, yarn, or embroidery thread can be used to make 2 tassels.Then, attach the tassel to the pointed end of the runner.If you don't want the runner pointed at the ends, you could attach several tassels across each flat end.
Step 13: If you want a decorative look, add piping to the edges.
The sewing machine's presser foot needs to be removed and replaced with a piping foot.The piping foot has grooves that will hold your piping in place as you sew it around the runner.cording is also referred to as piping.
Step 14: A border that stands out can be made with a different fabric.
You can add texture or color to your runner by choosing another fabric.The fabric should be as long as the side of the runner.If you want the borders to be wide, you can make them that way.To make a thin border, cut the strips in half.For a large runner, the strips could be closer to 3 inches.For a colorful border, use a few different colors for each strip of fabric.