A blackhead or comedone extractor is a tool used to remove whiteheads and blackheads.Comedones are small tools that look like small rods and have loops attached to either end or contain sharp lancets, they are designed to pull out the core of the pimple without damaging your skin.There are certain things that need to be done before using a comedone extractor.
Step 1: A good face cleansing routine is needed.
If you want to get clean, clear skin, washing your face twice daily is the most important thing you can do.If you are going to use a tool to remove skin problems, you should wash your face before using it.It's a good idea to wash your face in the morning before you go to bed at night.You can wash your face with a gentle cleanser and water.Don't use a harsh cleanser.Exfoliating and scrubbing your face can cause redness and inflammation.Don't scrub your face.You can gently massage the cleanser into your skin.You can wash the cleanser away by splashing water on your face.After washing your face, pat it dry with a towel.
Step 2: Your skin pores should be open.
Softening your skin will make it easier to get rid of it.If you want to open the pores, place a wet towel over your face or take a hot shower.You can use a steam treatment on your face.If the water is too hot, you can burn your skin.
Step 3: Wear gloves orDisinfect your hands.
If you want to prevent your hands from coming into contact with your face, you need to wash them with soap and water.You can use disposable gloves when using the tool.It's a good idea to wash your hands to prevent infections.This is important because the presence ofbacteria is bad for the skin.Cleanliness and hygiene are related to your level of success in clearing up acne.
Step 4: Make sure your skin is clear.
Before using an acne tool, you will want to wash your skin to make sure thatbacteria doesn't get pushed into your pores.Rub alcohol pads over the areas you want to treat before using the tool.Also wash the tool.If you don't use a tool that is sterilizable, you could end up introducing morebacteria to your face.Rub alcohol on a cotton swab to sterilize your tool.
Step 5: Pick the right tool for your problem.
Whiteheads need to be pierced with a lancet first before being removed with an extractor.A comedone extractor has two ends, each of a different size.You can choose the size of the blackhead you are removing from your face.A sharp lancet is used to pop open whiteheads before a blackhead is removed, but it takes more skill to use.It is best to avoid popping whiteheads due to the risk of infections.If you have a lot of whiteheads, see a doctor.If you're new to popping whiteheads with a sharp lancet, it's best to get it done by a professional.If you use the lancet wrong, it can cause damage to your face.The side of the tool that is used for blackheads is much safer and can be used at home.
Step 6: The comedone extractor can be used to remove your dead skin cells.
If you want to remove a blemish, you can centering the comedone extractor over it, and rocking it from side to side while applying a small amount of pressure.The blackhead will be pulled from the follicle and you will see oil oozing from it.If the blackhead does not come out with gentle pressure, don't try to force it.This can lead to infections.If you have a severe blackhead, you should see a dermatologist.
Step 7: If you are using a lancet, remove whiteheads.
You will need to pierce the whitehead with a lancet to break it open.Once the whitehead is broken open, you will want to centre it within the loop of the comedone extractor and rock the tool gently from side to side, applying slight pressure until it is pulled from the follicle.If you have any doubts about using the lancet, it is a good idea to see a dermatologist or aesthetician who is experienced in this area.Errors that could lead to scarring should be avoided.
Step 8: Take care of any bleeding.
It is possible that your skin may bleed after using the comedone extractor.To absorb blood, pat your skin with a piece of cloth.The bleeding should last a few moments if done correctly.You might have to apply firm pressure until the bleeding stops.
Step 9: Thoroughly clean the treated area.
Extra caution is needed when using rubbing alcohol pads to clean your skin.Before you put your tool away, you should clean it.It's important to remember that an extra effort toward good hygiene and clean living will maximize your success.