Snow chains can be very helpful when driving in snowy or icy conditions.They may need to travel on steep roads or in mountainous terrain.The idea of installing and removing snow chains is simple.Take the chains over the tires and drive slowly.If you put snow chains on your tires before you get to the snowy roads, it will be easier to install them during bad weather.
Step 1: You can get snow chains that match the size on your tires.
If you want to know which snow chains you need for your vehicle, you should know the size of your tire.There is a long string of letters and numbers on the outside edge of your tires.When you're shopping for snow chains, you need this information.The first, second and third numbers tell you the tire width, tire height ratio and diameter.The size of the tires will be indicated by the chain packaging.Don't be afraid to ask a store employee for help if you have questions.
Step 2: Remove the chains from the packaging.
If there are twists in the metal, hang the chains in a web shape.It is best to put your chains on before the process is done because it can take longer than you think.
Step 3: You should put the chains on the ground near the tires.
If your vehicle is rear-wheel drive, put the chains on both front wheels.Installation of the chains on all the tires is required for 4-wheel or all-wheel drive.You can put chains on all four tires of a front or rear-wheel drive vehicle for added safety and control during extreme weather conditions.
Step 4: Attach the snow chains to the tire.
Before you start, make sure your car is in park and the parking brake is on.Straighten the chains over the top of the tire so that they hang down.It should cover most of the tire.The chains should be straight across the width of the tire.To hold the chains in place, Tuck them between the bottom of the tire and the ground.Some snow chains have rings on them.During installation, the rings should rest on the bottom of the tire near the ground.This type of chain will require you to get under your car in order to install them, and may require a little adjusting to make sure they are on straight.
Step 5: You can expose the unfitting portion of the tire by driving your vehicle forward.
Before you disengage the parking brake, check your surroundings.Roll forward a bit when you put your vehicle in gear.Only a small portion of the tires are un fitted, so drive forward a little bit.
Step 6: The easiest way to get into the vehicle is to turn the wheel.
Turn the wheel toward the inside of the vehicle when you've pulled forward enough to ensure full tire coverage.It will be easier to finish securing the chains if you have better access to the connections.Turn your steering wheel to the right to point the tire at the other side.Turn your steering wheel to the left to point the tire at the other side.Put the car in park and use the parking brake again.
Step 7: To cover the rest of the tire, connect the chains.
From the inner part of the tire, connect the two hooked edges.The edges of the tires should be connected.The chains should be tightened so they are as snug as possible.Links can be tightened with a link-tightening tool, but don't use them on link unit chains.If the chains don't have built-in tightening cams, you can use a bungee cord with hook fasteners.Where snow chains are sold, these can be bought.
Step 8: The inner and outer connections of the chains should be aligned.
Make sure that the chains are straight across the tire.If the outside of the chain is loose, you will need to adjust the chains on either side to make sure they are straight.
Step 9: You should repeat the process for the other tires on your vehicle.
If you want to fit the chains over the top of the tires, you have to drive forward to expose the unfitting portion, then connect them together and make sure they are in alignment across the tire.You can install snow chains on your front and rear tires at the same time.The process will be sped up by this.
Step 10: Re-tighten the chains after driving about 100 feet.
Over the course of driving, the snow chains will shift a bit.The closer link or tightening cam can be used to re-tighten the chains after a short drive.
Step 11: As soon as you get to a clear road, remove your snow chains.
If the driving conditions improve or you see a sign that snow chains are no longer needed, take off your chains.It's hard on the road and your tires if you keep driving with your chains.
Step 12: The inside of the wheel has rings or chains.
To get to the connections, you will need to get down on the ground.Turn the wheel hard towards the inside to get better access.Pull forward a bit until you can fully access the connections if the tire is resting on top of them.Before you begin removing your snow chains, you need to remove the additional bungee cords.
Step 13: Lay the snow chains as flat as possible.
The chains are stuck under the wheel.If you lay the chains flat, you won't cause any damage to your tire when you drive over them.Make sure the chains aren't stuck around the wheel.
Step 14: Drive your vehicle slowly.
Pull forward so the tires can clear the chains.Carefully slide the chains away from the vehicle once they are fully exposed.Before putting the chains back in their packaging, allow them to dry.Don't twist or tangle the chains because they will be easy to install the next time.