It's a good idea to clean your car with Toothpaste.
toothpaste is good for cleaning things other than teethIf your vehicle's headlights are starting to look a little foggy, one of the simplest solutions is to polish the plastic outer covers with a soft cloth or brush.In a few minutes, the gentle abrasives in the toothpaste will make your headlights shine brighter and clearer.
Step 1: The headlights should be washed thoroughly with glass cleaner or soapy water.
You can spray your cleaner on the headlights.Use a microfiber cloth or soft automobile sponge to wipe away as much dust, dirt, and stuck-on debris as possible.The best way to get rid of the mess is to give your headlights a quick preliminary wipedown.
Step 2: The headlights should be dry with an absorbent towel or chamois.
If you have standing streaks or droplets of water on your headlights, you should wash them with a towel or chamois.It's a good idea to dry off the edges of the covers.Make sure the towel you use is lint-free.If you leave behind small fibers, they can become stuck on the headlight covers.While the headlights are still wet, you can apply the toothpaste to produce a lather similar to soap.
Step 3: It's a good idea to tape off the area around your headlights.
Stick strips of automotive masking tape or painter's tape over the paint at the top, bottom, and sides of the lights.Make sure there is no exposed paint near the portion of the lights you will be cleaning after inspecting your work closely.Any paint that is not covered with tape could be damaged by the pressure of polishing and the toothpaste.
Step 4: There is a dime-sized blob of toothpaste.
If you want to apply the toothpaste to the cloth or sponge, squeeze it directly onto the center of the plastic covers.The toothpaste should be spread in widening circles until it covers the headlights.It is best to start with a small amount and add more later as needed.It is important to use an ordinary type of toothpaste.The lights appear foggy because the gel toothpastes don't contain abrasives, which are what is responsible for chipping away at the dingy layer of oxidation.
Step 5: Use a microfiber cloth or sponge to Polish the headlights.
Move your cloth or sponge in a circular motion to clean the covers from top to bottom.You should be able to see that even the heaviest gunk disappears within seconds.If your headlights don't look any cleaner after your first few passes, use a soft bristled brush to increase your coverage and really work the toothpaste into the plastic.An old toothbrush is perfect for the job.It may take a little bit of elbow grease to get your headlights to look like new.Don't be afraid to dig in and take your time.
Step 6: Warm water can be used to rinse the headlights.
If you don't have a spray bottle or hose, you can use water from a bucket or similar container.Continue rinsing until the water runs clear to ensure that you have flushed away the toothpaste.Don't forget to remove the tape from your headlights when you're done.If you miss toothpaste, it will dry to a cloudy film, leaving you back where you started.
Step 7: You can protect your headlights from the sun with a coat of UV-resistant sealant.
Wet a folded paper towel with the sealant solution.Aim for full coverage with long, sweeping strokes.Only a single coat of sealant is required.You can get a bottle of UV-resistant headlight sealant for a few dollars at any automotive supply store, as well as most supercenters, gas stations, and convenience stores.Exposure to the sun's rays can cause the formation of oxidation on your headlight covers.
Step 8: Allow the sealant to cure for 10 to 45 minutes.
If you park your vehicle outdoors, it can get some sunlight.After a few minutes, most headlight sealants dry to the touch and cure to full strength within half an hour.Depending on humidity levels and the amount of sunlight available, the exact cure times can vary.If you have a UV lamp, you can shine it on your headlights for 10 minutes or until they are completely dry.Wait at least 8 hours after applying headlight sealant to wash your vehicle.
Step 9: The process can be repeated every couple of months.
It is possible to restore your car's headlights with toothpaste, but it is not a permanent fix.They need to be cleaned and sealed every couple of months in order to stay bright and clear.If you do a lot of driving, you may need to increase the number of times you clean.