Problem with my 65"Mitsubishi television can be found in the "Blinking" section of the website.

The menu button is on the remote.What is on the screen?Make sure the remote's layer switch is on.

Plug the AC cord into the wall power outlet for 60 seconds before plugging it back in.If the condition of the TV is the same as before, please call the Consumer Relations department.Please provide the model number, serial number and proof of purchase.

The green light blinks when the TV is in the booting up process.The green light blinks for 20 to 60 seconds depending on the model.Plug the AC cord from the wall power outlet if the blinking continues for more than 60 seconds.Wait for 60 seconds before restarting the TV.

It is possible to resolve this issue by loading the software for your model.Check out the downloads section.

If TV still doesn't power on, you can remove all connections to the TV and then try again.

A green light indicates that the TV is ready to start.There are many possible causes of a TV shutting down.invalid digital data was sent to one of the inputs

Digital broadcasts from over-the-air television stations and cable companies contain a lot of data.The data can be corrupted while being transmitted or input in an incorrect format.The data could cause the TV to shut down.

It should not be considered an issue if it only occurs once or once every several months.If the occurrence is more frequent such as every day or every hour, you may want to look into your satellite box/dvd/blu-ray player.

Wait for 60 seconds before plugging the AC cord into the wall power outlet.

You may want to reseat the lamp if the TV has not powered on and the Solid Red light is still on.

To find out if your lamp is eligible for a warranty, check www.mitsuparts.com.

Check your owner's manual for instructions on how to replace your lamp.You can check the documents and download a section.

If your lamp door cover is not installed correctly, you will receive a blinking yellow light.The door should be flush against the TV.

If the door is not installed correctly, please call.Please provide the model number, serial number and proof of purchase.

Leave the TV in the off position for at least 15 minutes to allow it to cool down.

If the door is not installed correctly, please call.Please provide the model number, serial number and proof of purchase.

The diagnostic code used by the Consumer Relations department is the sequence of blinking LEDs.

If you want to recycle AC power, you should remove the AC cord from the wall power outlet and wait 60 seconds before applying AC to the TV.

If the TV has not fully recovered after you recycle the AC power, please contact the Consumer Relations of the company.Please provide the model number, serial number and proof of purchase.

If the TV doesn't turn on from the unit itself, the remote may need new batteries.

If the problem doesn't go away, please contact Consumer Relations.Please provide the model number, serial number and proof of purchase.

The TV needs to be started.The TV will be reset if this process is done.The menu was followed by 1 2 3.The TV will change settings.The TV will be on channel 3 after the process is done."snow/static noise" should be audible.

If you still don't hear audio, please contact the Consumer Relations department of the company.Please provide the model number, serial number and proof of purchase.

The audio format is mentioned in the signal.Some broadcasters may be sending digital descriptors about the audio that the TV does not recognize.

If you can't receive audio from a single channel, it's probably not a fault of the TV, and you should contact the broadcasters of that channel or your cable provider.

Press the button on your TV remote.An icon should be displayed in the upper right corner.

Please call if the issue continues.Please provide the model number, serial number and proof of purchase.

Leave the TV in the off position for at least 15 minutes to allow it to cool down.

When there is no video signal, this message appears.There is a chance that this can be caused by an invalid HD channel.There is no valid video from a digital or analog device.

Make sure your IR/controller device doesn't send a power down command to the TV.The TV could be receiving a power off command.All IR sending devices should be pointing away from the TV.If you have a controller device installed to the TV, you need to make sure it doesn't accidentally send power off commands.

If you receive a loading icon on the bottom of the screen or a connection timed out error, this means your TV cannot reach the final destination server.

The two most likely scenarios that will cause this are a firewall blocking the incoming content and the bandwidth being too limited to receive the data.

Your area has a lot of broadband connections.Peak hours are likely to show reduced performance.

To use the internet on a 2010 model year TV, you will need to press the INTERNET button on your remote control.Older model year remotes do not have a button for internet access.

Your area has a lot of broadband connections.Peak hours are likely to show reduced performance.

Check the connection on the back of your TV to make sure it's connected to the open internet port.

The TV is not allowed to connect to a network if you don't have your default gateway or SubnetMask data.

To use the internet on a 2010 model year TV, you will need to press the INTERNET button on your remote control.Older model year remotes do not have a button for internet access.

If you receive a loading icon on the bottom of the screen or a connection timed out error, this means your TV cannot reach the final destination server.

The two most likely scenarios that will cause this are a firewall blocking the incoming content and the bandwidth being too limited to receive the data.

Your area has a lot of broadband connections.Peak hours are likely to show reduced performance.

The AC-DC adapater and the signal from the source device through the HDMI connection are required in order for the 3DA-1 to power on.

The format setting issues on 3DC-1000/3DA-1 are related to this section.Make sure to look closely as some formats look similar, and find the picture that most looks like what you see on your TV screen.

The original picture is directly from the source device.

Set TV to "side by side"

The Checkerboard solution is to set the TV to "top and bottom".

The top and bottom solution is to set the TV to side by side.

Side by side solution: Set TV to top and bottom.

The source device is not a 3D source.

Set TV to "AUTO" or "CHECKERBOARD" if you want to side by side.

The source device is not a 3D source.

The top and bottom solution is to set the TV to "AUTO" or "CHECKERBOARD".

The 3D format that the incoming signal is accepted in is not a valid one.There is a list of valid formats.

You can use this section to find format setting related issues on 3D TVs.Make sure to look closely as some formats look similar, and find the picture that most looks like what you see on your TV screen.

The original picture is directly from the source device.

Set TV to "side by side"

The Checkerboard solution is to set the TV to "top and bottom".

The top and bottom solution is to set the TV to side by side.