Sewing machines vary from model to model, so if you have your manual handy, it may have more specific instructions for your particular machine.It is not the end of the world if you do not have your manual.Take a second to get familiar with the pieces, and then thread the bobbin and needle.It should take no more than a few minutes to get your machine ready to sew.
Step 1: The bobbin should be winded.
The thread that comes up through the base of your machine is supplied by the bobbin.The thread connects with the thread on the needle.If you want to wind the bobbin, insert the thread through the hole in your spool and wind it around a few times.Place the bobbin on the small pin so that it is locked in place.Attach your thread to the larger one.Slowly apply pressure to your pedal and watch the bobbin wind.The pedal should be stopped when the bobbin is full.You don't have to worry about threading a bobbin if you have pre-threaded bobbins.
Step 2: The bobbin has to be loaded.
Load the bobbin into the case below your needle after threading it.The case can be revealed by popping off the cover.The bobbin should be inserted into the case on your machine.An arrow should be used to show the direction of the thread.Check your machine's specific instructions for loading the bobbin if you have a manual.With some machines, you just pop the bobbin into place, while others require you to remove the case and insert the bobbing before you load it.After the bobbin is loaded, put the cover back on.
Step 3: Make sure you thread the machine's top parts.
You will need to guide your thread through the top area of your machine after your bobbin is in place.The thread should be placed on the larger pin at the top of the machine.The machine should tell you where the thread goes.Pull a piece of thread from the top of the machine and bring it down through the first slot.The thread should be brought back up to the top of the machine.There should be a diagram on your machine that shows where the thread should go.
Step 4: The thread should be inserted into the eye of the needle.
Put the thread through the eye of the needle on your machine.Pull the thread until it is taut.To connect the top and lower thread, you should leave at least a few inches of thread.The needle should be replaced after 2–3 bobbins so it doesn't get dull.If you don't, your stitches may look messy.
Step 5: The thread can be caught.
The knob on the side of the machine can be used to catch the thread.The bottom thread should come up through the machine base as you do this.To push the thread strands to the back of the machine, use a ruler or other flat object.Your machine is ready to use.
Step 6: Check your stitch setting.
Before you start sewing, make sure you check your settings.The digital display on your sewing machine can show you the stitch setting.To change the stitch setting on your display, turn the knob or select a new setting.Most patterns call for a straight stitch, which is the number one on most machines.To find out if this is correct and whether you need to make any other adjustments to use a specific stitch setting, be sure to check your manual.Depending on the type of machine you have, your machine may automatically adjust the tension for you or you may need to manually adjust it.
Step 7: The fabric should be under the needle.
The presser foot can be raised if your machine is set correctly.You can raise the presser foot with a lever on the underside of your machine.Put your fabric in the presser foot and lower it to hold it in place.If you can't locate the presser foot, check your manual.A piece of scrap fabric can be used to test the stitch.
Step 8: The pedal needs to be applied with some gentle pressure.
Apply gentle pressure to the pedal when you are ready to sew.The teeth on your machine will move the fabric as you sew.Keep your fingers away from the needle as you apply gentle pressure on the fabric.If you want to apply pressure to the pedal, make sure it is easy for you to reach.If the stitches look sloppy or the fabric is going fast, stop the machine and make adjustments.The sewing manual has sections to help you solve problems.You can go back through the threading process and check the tension on your machine to find a solution.