Fly fishing uses sy Casting is a type of casting used in fly fishingThe advantage of Spey casting is that it allows the caster to throw their line long distances in a straight line.It's useful on wide rivers that offer challenges.Spey casting seems like a difficult type of casting to perfect, but it is a relatively simple technique.You can discover a new and exciting type of fishing with a little work and experience.
Step 1: Stand on the ground and find firm ground.
You can move your feet on the lakebed.There is a piece of ground that is firm and flat.If you move when you cast, you could lose control of your pole.
Step 2: Stand as if you are throwing a ball.
Stand with your feet parallel to each other and place your non-dominant foot in front of yourdominant one.In order to throw a successful cast, you should relax your legs and hips.Don't move your feet when you cast.
Step 3: If the wind is blowing in one direction, place your hands in it.
Put your hand on the top grip if the wind is blowing upstream.Put your hand on the top of your grip if the wind is blowing downstream.As you cast and wait for a bite, you will have more control over the poll.
Step 4: If you want to cast longer, place your hands apart.
If you want to cast longer, widening the space between your hands can be helpful.
Step 5: Don't hold the rod in a tight position.
You won't be able to react quickly if you hold the rod tightly.If you hold the rod tightly, it will tire you out a lot quicker.
Step 6: When you cast, tilt your body 90 degrees.
Instead of moving your body completely, gently move your knees and hips.You should make sure your feet are on the ground.
Step 7: The rod should be at the water line.
The tip of your rod should be at the water line.It shouldn't be more than 2 inches above the water line.You will be able to build up a lot of strength when you sweep the rod back and forward.
Step 8: Drop your line and let it wash down the river.
Allow your line to wash downstream before casting.Depending on how comfortable you are at spey casting, you can allow it to wash up to 30 feet.It's best to keep this distance short.As the line floats down stream, keep it taut.Allowing the line to wash downstream sets you up for a backwards cast.This is called a line stick.
Step 9: Find your target on the water.
Your target is where you want your bait to go after you cast it.Say you want to go to the opposite bank in front of you.The tip of the pole needs to end up 180 degrees behind you if you want to complete the back cast.The "back cast" is when you pull back on the pole.The forward cast is the first part of a movement.
Step 10: The rod should be moved backward 180 degrees from your target.
After your line has traveled downstream, sweep the rod backward to begin the back cast.As you jerk back on the pole, it will go behind you.The cast should be 180 degrees from where you plan to throw it.
Step 11: A big D loop can be created by casting your rod far back.
The D loop is the loop that the line makes with the rod after you cast backwards.It will be easier for you to cast far forward if you have a larger D loop.Throw your line back as far as you can before casting.You will have to put more effort into your cast if you have a small or narrow D loop.
Step 12: After you swept the line backward, pause.
Once it reaches the right position behind you, 180 degrees from the target, and the D loop is set up, the back cast is complete.You can allow the anchor to move and align by pausing.You will not be able to throw as far as you want if you don't allow the anchor to move.
Step 13: The line should sink below the water.
You will have less line on the surface of the water if you start with a big D loop.When you bring your line behind you to make the D loop, make sure you throw your forward cast quickly.The easier your cast is, the less line you have on the water line.You should only have 2 inches of line at the waterline.
Step 14: Go forward at 180 degrees.
Casting from your back to your front at 180 degrees will allow you to target a specific spot on the water and put a lot of energy into your cast.To turn and cast your line 180 degrees, you need enough room behind you.
Step 15: You can use a spey rod.
The rod can be as long as 21 feet.Most modern rods are between 12 and 15 feet long.You will be able to cast further and more accurately if you use a rod specifically designed for spey casting.If you attempt to use a regular fishing rod, you may have trouble getting the distance you want.
Step 16: You should wear fishing waders.
If you want to protect yourself from getting wet and becoming cold, you need to wear fishing waders.Waders are rubber pants/boot combo that go up to above your waste and are secured to you by suspenders.You won't be able to fish for long without fishing waders.
Step 17: Side shields are included in the glasses that you use.
UV protection and side shields are included with the purchase of high quality glasses.There is a chance that a hook or lure could damage your eyes.
Step 18: There is a brimmed hat and sunblock.
When fishing, you should take precautions to protect yourself from the sun.The best way to protect yourself from the sun is to apply sunscreen with a 30 SPF or higher rating.You can shade your face from the sun with a brimmed hat.You will get a double layer of protection.