The quick fix is to reset the switch.
Responsive design allows for a convenient experience that matches your device's screen size.To get the best experience from our website, please follow the instructions below.
If you're using Internet Explorer 9 or earlier, you will need to use an alternate browser or upgrade to a newer version of internet Explorer.
Not heating, long dry time, and certain operation errors can be fixed without a technician.Electric and gas dryers are covered in this content.
If the unit is displaying an error code, you can learn how to fix it.Proceed to Step 2 if the unit has not displayed an error code.
If the unit has been used recently, let it cool down and empty the drum.The instructions can be found in the following link.
If you don't get a copy of your owner's manual, you can use a time dried method.
The In5 may not display if you run a timed dry method.If you get an error code, restart the heat test.
Since there is no error code on the unit, we need to know if the drum feels warm or cold after the heat test.
This is a power issue if there is no error code or bars on the flow sense and the dryer feels cold.
The plug should be plugged into a grounded outlet that matches the dryer's rating plate.
To clear the power surge inside the dryer's circuit breaker, turn it off from the main house.
The dryer needs a repair service if it isn't heating up.You can request a repair on our page.
Gas should be flowing throughout the house.If gas is running in the house, use another gas unit.Contact your gas company if there is no gas in the house.
The unit will need a repair service if you have done the recommended solution in this article.You can request a repair on our page.
There is air flow in the unit.There is a chance that this is the culprit of the long drying time.
Energy saver mode can be used to reduce energy consumption.Pressing the ENERGY SAVER button will turn off energy saver mode.
Energy saver can still be used for other cycles.The energy saver button has a light on it.
Long time drying occurs when the lint filter is dirty.After every cycle, clean the lint from the filter.Pull the lint filter straight up when you open the dryer door.
If the lint filter is dirty and needs to be cleaned, you can wash it in soapy water and let it dry before you replace it.
It may be better to use time dry instead of sensor dry when drying smaller loads.
The load is too large if the clothes are not able to tumble.
The cloths are dried out by the sensor.If there is a problem with the sensors, the unit will shut off before the items are dry.
The hot, humid air from the dryer needs to go somewhere or it will stay in the drum and clothes.The exhaust system is severely restricted if there are 2 or 4 bars on the flowsense.
lint build up at the rear exhaust duct can cause a long time drying in the dryer.
If you need a professional technician to clean your vent, you should contact a local vent cleaning company.
Air obstruction can be caused by a crushed or damaged exhaust.If you can, check the entire exhaust duct to make sure it isn't damaged.
It will be hard to trace when the ductwork is too long or too many bends.When the machine is running, it is a good idea to check the exterior of the house.
Contact a local vent cleaning company to clean the vent for proper inspection and repair.
The unit may need a repair service if you have tried all the recommended solutions.You can request a repair on our page.
The error codes show that the dryer's exhaust duct is at least 75% blocked.
The hot, humid air from the dryer needs to go somewhere or it will stay in the drum and clothes.The exhaust system is severely restricted if there are 2 or 4 bars on the flowsense.
lint build up at the rear exhaust duct can cause a long time drying in the dryer.
If you need a professional technician to clean your vent, you should contact a local vent cleaning company.
Air obstruction can be caused by a crushed or damaged exhaust.If you can, check the entire exhaust duct to make sure it isn't damaged.
It will be hard to trace when the ductwork is too long or too many bends.When the machine is running, it is a good idea to check the exterior of the house.
Contact a local vent cleaning company to clean the vent for proper inspection and repair.
A nP error code on the dryer's display indicates that there is a problem with the electrical wiring in the home, and that no current is being detected at the heater.
There is a PS error code on the dryer's display that indicates that there is improper voltage with the power cord, which could be caused by the white and red wire connections being reversed.
Make sure the power cord is plugged into a grounded outlet that matches the dryer's rating plate.
To clear the power surge inside the dryer's circuit breaker, turn it off from the main house.
If the nP error is showing, the home's outlet may need to be checked by a licensed electrician to make sure the correct voltage is supplied to the dryer.
The dryer needs a repair service if it isn't heating up.You can request a repair on our page.
The error codes show that the dryer's exhaust duct is at least 75% blocked.
The hot, humid air from the dryer needs to go somewhere or it will stay in the drum and clothes.The exhaust system is severely restricted if there are 2 or 4 bars on the flowsense.
lint build up at the rear exhaust duct can cause a long time drying in the dryer.
If you need a professional technician to clean your vent, you should contact a local vent cleaning company.
Air obstruction can be caused by a crushed or damaged exhaust.If you can, check the entire exhaust duct to make sure it isn't damaged.
It will be hard to trace when the ductwork is too long or too many bends.When the machine is running, it is a good idea to check the exterior of the house.
Contact a local vent cleaning company to clean the vent for proper inspection and repair.
Make sure the door is open and that there are no articles of clothing stuck on it.
Is there any damage to the frame of the unit if it is brand new?If that is the case, please contact the dealer.
An E13 error code can be found on the dryer's display if the drain hose is crushed, blocked, or frozen.
The dryer won't drain well if the drain hose is extended.The standard drain hose is recommended.
The dryer can be started again if the drain hose is free of obstructions.
The unit will need a repair service if the E13 error code occurs again.You can request a repair on our page.
An FO error or a flashing INSERT FILTER on the dryer's display indicates that the lint filter should be checked to make sure it is inserted correctly.
The dryer will stop working if the lint filter is not inserted correctly.Remove the lint filter and put it in the housing.
The unit may need a repair service if the error continues.You can request a repair on our page.
There is an error with the Humidity Sensor on the dryer's display.
The dryer will run for 21/2 hours because of the error code, which may seem like the dryer is not drying.
The sensors on the inside of the dryer need to be cleaned if the error is displayed.Before attempting another cycle, allow the sensors to fully dry.
The unit may need a repair service if the error code continues.You can request a repair on our page.
A nP error code on the dryer's display indicates that there is a problem with the electrical wiring in the home, and that no current is being detected at the heater.
Make sure the power cord is plugged into a grounded outlet that matches the dryer's rating plate.
To clear the power surge inside the dryer's circuit breaker, turn it off from the main house.
If the nP error is showing, the home's outlet may need to be checked by a licensed electrician to make sure the correct voltage is supplied to the dryer.
The dryer needs a repair service if it isn't heating up.You can request a repair on our page.
The unit may need a repair service if the error code continues.You can request a repair on our page.
There is a PS error code on the dryer's display that indicates that there is improper voltage with the power cord, which could be caused by the white and red wire connections being reversed.
Make sure the power cord is plugged into a grounded outlet that matches the dryer's rating plate.
To clear the power surge inside the dryer's circuit breaker, turn it off from the main house.
The power cord and wall outlet should be checked by the installer if the unit was just installed.
The dryer needs a repair service if it isn't heating up.You can request a repair on our page.
Refer to the owner's manual for installation instructions.You can find a copy on our page.
There is a tE1 error code on the display of the dryer.The tE1 error code can be seen on the dryer's display.
The unit may need a repair if the tE1 error code occurs again.You can request a repair on our page.
A tE2 error code on the display of the dryer indicates a problem was found with the thermistor.The tE2 error can be caused by the extra humidity in the dryer's vent during the steam fresh, steam sanitary, or steam option cycles.
The tE2 error code can be seen on the dryer's display during the SteamFresh, SteamSanitary, or the steam option.
The unit may need a repair if the tE2 error code occurs again.You can request a repair on our page.
There is a tE3 error code on the display of the dryer.The tE3 error code can be seen on the dryer's display.
If the tE3 error code occurs again after the dryer is reset, the unit may need a repair service.You can request a repair on our page.
Water must be filled up to the MAX indicator lines before a steam cycle can be used.To make sure the drawer is completely closed and the steam feeder is full, check it.
If you want to power the unit off and back on again, press the start button and select the STEAM cycle.
The check filter was designed to remind people to clean the lint filter before each use to ensure great drying.
When you turn the cycle knob to select a drying program, the indicator goes off.
A child lock reading on the dryer's display is not an error code, but an indication that the feature is active.
The Child Lock feature can be disabled by pressing and holding the key labeled CHILD LOCK for 3 seconds.
The control panel is disabled when the child lock feature is active.
This is normal.The cooling portion of the cycle is run by the machine.The last 5 minutes of the cycle are when the cooling portion begins.
The display does not indicate that there is a problem with the dryer.Wrinkle care works at the end of the drying cycle and will continue to tumble the dryer drum to prevent wrinkling.
The drum will be off for 6 minutes.It will last up to 3 hours.The Wrinkle Care option will be turned off if the door is opened during this time.
Plug the dryer into the electrical outlet and power it off.
Sanmi is the author of a help library article.Please let him know what you think about the page.
We apologize for the time delay.
Get answers to your questions about product setup, use and care.We can help.