What do you do if your water heater pilot light won't light?
What do you do if your waterheaterpilotlight won't light?
When the waterheaterpilotlight goes out, first try relighting it, following the directions on the waterheater label. If the pilot doesn't relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple.
How do you light a pilotlight manually?
Turn the gas regulator valve to the “pilot” position. If the waterheater has a manual “ignite” button, press that to light the pilot. If it doesn't have the button, or the button fails, press the regulator valve and hold a grill lighter or long match to the pilotlight valve until the pilot ignites.
How do you light a pilot stove?
- Gear up. Get a microfiber cloth and a lighter or match; a long-wand lighter is best.
- Shut down.
- Remove the grates.
- Open up the stovetop.
- Find the pilot port.
- Clean the pilotlight area.
- Light the pilot light.
- Close it up.
How do you reset the pilot light?
- Step 1: Turn off your furnace.
- Step 2: Locate your gas valve.
- Step 3: Hold down the red button.
- Step 4: Light the pilot light.
- Step 5: Let go of the button.
- Step 6: Turn your gas back on.
- Step 7: Turn your furnace back on.
How do I relight the pilot light?
Turn the knob to “Pilot” and hold down the “Reset” button. Using a long lighter, bring the flame close to the pilot opening. This should ignite the pilot light.19 בינו׳ 2021
Can you manually light an automatic pilot light?
By design, an automatic pilotlight does not need to be lighted or relighted; it turns on and off by itself. Only a pilotlight with a continuously burning flame — called a standing pilot— requires manual relighting if the pilot flame goes out.19 באוג׳ 2021
Why does my hot waterheater igniter not ignite?
If the igniter fails, the burner will not light. To determine if the igniter is defective, first make sure the igniter is getting voltage. If the igniter is getting voltage, but it doesn't glow, this indicates that the igniter is defective and should be replaced.
What do I do if my pilotlight won't light?
- Find your gas valve.
- You need to turn the valve to the off position for at least three minutes.
- Once you have had the valve at off for a few minutes, switch it over to pilot setting.
- You will need a match that is lit.
- Set the pilot valve to the on position.
How do you reset the igniter on a water heater?
Reset the pilotlight There should be a button to release the gas. Usually this is a red button or a button with a fire logo or image. Push the button until it clicks. Now push the igniter switch while holding down the button.17 ביולי 2017
How do I know if my thermocouple is bad on my water heater?
If the pilot lights but the flame goes out as soon as you release the button after holding it for 60 seconds, then the thermocouple is bad. It's possible to replace the thermocouple without removing the burner assembly, and many repair people do this.
Is it bad if the pilotlight goes out?
Older furnaces that run on natural gas are usually equipped with a pilot light. This tube is fitted with a safety valve (the thermocouple), which stops the flow of gas if the pilotlight goes out. This prevents gas from building up in your furnace, posing a safety hazard.9 בינו׳ 2020
Why would a pilotlight just go out?
A faulty, misaligned, dirty, or damaged thermocouple is often the culprit behind your pilotlight going out. The thermocouple is an automatic safety shutoff device that prevents the gas valve from opening if the pilotlight is out.
How often do thermocouples need to be replaced?
How to Tell if You Have a Bad Thermocouple? Thermocouples can last up to 10 years if properly installed and maintained, while furnaces can last 15-20 years, although either may wear out sooner in multifamily units.
How do you test a waterheater thermocouple?
- Light pilot. Hold down pilot button for 30 to 60 seconds.
- Relase pilot button.
- If pilotlight goes out when button is released, then thermocouple is most likely at fault.
How do you know when to replace thermocouple?
After about a minute, when you're sure the probe has gotten hot, place one lead on the shaft of the thermocouple and the other lead on the connector. If the reading is less than 25 millivolts, the thermocouple is bad and needs to be replaced.15 בדצמ׳ 2021
Can you clean a thermocouple on a water heater?
Water Heater Thermocouple Cleaning in 5 Steps Cut the fuel supply to the water heater. This is always the first step when working on a water heater. Clean the thermocouple - using the emery cloth sandpaper, sand the ends of the thermocouple and then give it a finishing touch with the lint-free cloth.
Can I replace a thermocouple myself?
Thermocouples are designed to detect a pilot light's loss of heat and close the gas valve to prevent a gas leak. Replacing a thermocouple is a relatively easy fix that can take less than two hours.
How do I know if my thermocouple is going bad?
If you can't get the flame to light at all, and you're sure the gas is on, there's probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that's the sign of a thermocouple malfunction.15 בדצמ׳ 2021
How do you maintain a thermocouple?
- Do not allow excessive bending of the thermocouples.
- Use protection tubes for corrosive atmospheres.
- Always inspect protection tubes when changing thermocouples.
- Do not locate the thermocouple too close to a heating element.