Health

Why is my Maytag washer not draining or spinning?

A top load Maytag washer not draining may have a defective lid switch assembly. On top-loading washers, draining and spinning will only occur if the lid is properly closed and activates the switch. Try depressing the lid switch with your finger to see if the machine drains and spins.Apr 1, 2021

Why won't my Maytag washer agitate or spin?

Common solutions for: Maytag Washer won't spin or agitate. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. If the washer is overloaded, the motor coupling will fail in order to protect both the motor and transmission.

How do I get my washer to drain and spin?

- Perform a Master Reset. Unplug your washer for about one minute. - Test the Lid Switch Assembly. - See if the Drain Hose is Kinked. - Check the Drain Hose or Pump for Clogs. - Clean out the Coin Trap. - Check the Water Level Control. - Schedule Washing Machine Repair.

How do you fix a Maytag washer that doesn't drain?

If no blockages are visible, unclamp the hose from the tub end to check for and remove obstructions. Reconnect the inner hose to the pump and tub. Replace the washer's front panel. Reconnect the outer hose to the drain, making sure the end of the hose is 30-96″ above the floor for proper draining.Apr 1, 2021

How do I get my washing machine to drain manually?

- Step 1: Turn off the power and lay down towels. For safety, unplug the machine. - Step 2: Locate the drain hose at the back of the washing machine. - Step 3: Drain the water. - Step 1: Turn off the power and lay down towels. - Step 2: Locate the drain hose. - Step 3: Drain the water. - Step 4: Scrub the filter.

What causes a washing machine not to drain and spin?

If the washer won't drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.

How do I get the water out of my washer that won't spin?

https://www.youtube.com/watch?v=oFB1jEdXVsQ

Why is my washer not rinsing and spinning?

The most probable cause is a clogged pump filter. The pump filter should be cleaned every three months or when it's clogged. To clean the pump filter, open the cover to expose the filter. Some washing machine models have a small hose stuck behind the cover to drain the water inside the filter.

How do you force a Maytag washer to drain?

- Pull the washer away from the wall and turn off its power and water connections. - Scoop out any remaining water in the washer drum. - Unhook the drain hose from the wall or sink drain and empty residual water into a bucket.

How do you fix a flooded washing machine?

- Turn Off the Water. The first step to cleaning up a washing machine flood or overflow is to turn off the water. - Unplug the Washer. - Remove Standing Water. - Remove Damaged Items. - Dry Out the Flooded Area. - Empty the Washing Machine. - Disinfect and Deodorize Your Home. - Restore and Rebuild the Damaged Area.

What causes a washing machine not to drain water?

There are a few possibilities why your washing machine won't drain. Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.

Why is my Maytag washer not putting out water?

If your Maytag washer is not filling, check your fill hoses: Check household faucets. Hot and cold water supply lines must be connected and turned on. Check for kinks in inlet hose.

Is there a reset button on a Maytag washer?

Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.

How do you clean a Maytag washing machine drain pump?

https://www.youtube.com/watch?v=pWU0NonOHhA

How do you fix a washer that won't fill with water?

https://www.youtube.com/watch?v=ft1cBPx8l0Y

How do I clean my Maytag top load washer pump?

Place a broad, flat container beneath the drain pump filter to collect the drain water. Release the black hose from the hose clip, remove the plug, and drain the hose into the container. Empty the container. Repeat this procedure if necessary until all the water has drained.