There are lots of ways to make earrings.You can turn it into an earring if you put a hook on it.The fabric earrings are popular.They are cute and shabby.There are many ways to make them, from using plain fabric to lace to fabric-covered buttons.You will end up with something cute and unique if you choose any of the methods.
Step 1: You can make your template out of thin cardboard.
A shape can be drawn on a piece of cardboard.The starter shapes include circles, triangles, hearts, and leaves.Use a sharp pair of scissors or a craft blade to cut the shape out.
Step 2: Attach your double-sided fabric to it.
Put your fabric on the ironing board.The face-down is placed on top.The manufacturer's instructions tell you to iron it.There is a shiny side and a matt side.It should be shiny-side down.It will be a little different for each brand.For a few seconds, you will need to iron the interfacing using a low-heat, no-steam setting.
Step 3: Cut the fabric into four equal pieces.
The pieces should be bigger than the template.Don't cut it into your final shape just yet.
Step 4: Remove the backing.
The backing of the double-sided fabric pieces needs to be removed.You should now have four small pieces of fabric, with the right-side on one side and the glue side on the other.
Step 5: There are two pieces of fabric that need to be fused together.
Place your fabric scraps on the right side facing out.For a few seconds, iron the stack on the ironing board.With the remaining fabric scraps, repeat this step.The right side of the fabric should be on both sides.Follow the instructions of the manufacturer.You can iron it for a little longer if you use the same heat setting.
Step 6: Once the fabric scraps are cool, trace your template onto them.
The fabric scraps will be very hot and flimsy at first, but will stiffen as they cool.Once they cool down, trace your template onto them.If your fabric is light-colored, use a pen to trace the template.If the fabric is dark, use chalk.Save the template for another project when you are done.
Step 7: Use a pair of scissors to cut the earrings out.
Cut just inside the lines that you wear.You won't have to worry about the lines showing.The fabric will not be damaged by the fusible interfacing.
Step 8: To punch a hole in an earring, use a thumbtack.
If you don't have thumbtacks at home, you can use a pushpin or a thick needle.If you want to make statement earrings, make a larger hole and add a small accessory into it.This method is used for earrings.Attach the top of each earring to a blank post earring if you don't like hook earrings.
Step 9: An earring hook has a twist.
To open the loop at the bottom of the earring, use a pair of needle nose pliers.You will warp the loop if you pull it open.It's like opening a door.It's a good idea to put a jump ring first.The earring hook needs to be kept intact.Use the same technique to open the jump ring.
Step 10: Attach the earring hook to the hole.
Use your needle nose pliers to close the loop.Pinch the loop shut with your needle nose pliers if there is a small gap.Add the earring hook if you want to add a jump ring.The same technique is used to close the jump ring.
Step 11: There is embroidered bridal lace fabric.
Don't worry about the color, you can always paint it.Look for a design that appeals to you.The trim section of a fabric store would be a good place to find lace.
Step 12: You can cut the lace to the shape you want.
There is a floral design on most types of lace.Some may have a scrolled design.You can find a section of the design that you use best by taking a look at your lace.To remove it, use a pair of scissors.Cut through the mesh around the design.Cut across an embroidered design.Cut out two designs for each earring.
Step 13: The lace can be painted with fabric stiffener.
Place the pieces of lace on a smooth surface, such as a sheet of wax paper, plastic wrap, or foil.Put fabric stiffener on one side and let it dry.Paint the other side after flipping the lace over.Adding some "weight" to the lace will help it stiffen.If you don't have a fabric stiffener at home, use a decoupage glue.
Step 14: If you want, you can paint the lace.
You can use a variety of paints for this.Water it down first, and apply it in several thin layers if you are using fabric paint.This way, you won't lose the design.Let it dry before painting the other side.
Step 15: Let the lace dry.
This could take a few minutes to several hours depending on the products you used.Refer to the label on your stiffener for more specific instructions.
Step 16: An earring hook can be opened.
A pair of needle nose pliers can be used to open an earring hook.Pulling the loop open can weaken the metal.
Step 17: The earring hook goes through the lace.
The top of your design is where you want it to be.Close the loop you just opened to the edge.
Step 18: The earring hook should be closed.
To seal the lace inside, use your needle nose pliers to twist the loop back shut.If there is a small gap between the earring hook and the end of the loop, pinch it shut with your nose plies.
Step 19: The fabric store has an aluminum cover button kit.
If you don't have a button cover tool in your kit, you will not be able to put the buttons together.You have the option of choosing any size kit.
Step 20: You can trace a circle onto your fabric with the included template.
There is a template on the back of most button cover kits.To trace the template onto your fabric, use a pair of scissors and a pen or pencil.One circle is required for each button.There is a plastic template inside the package.Use that if your kit is one of those.
Step 21: The circle of fabric needs to be cut out.
The edges will be tucked inside the button.
Step 22: The fabric should be put into the tool.
There are two parts to a cover button kit: a large squishy part and a small hard plastic part.The large, squishy part is what you are looking for.Put the fabric over the large squishy part.
Step 23: The button needs to be pressed into the tool.
Make sure you put the button into the tool.Be careful as the fabric may shift while you are doing this.You will need to adjust the fabric if it shifts.You want to have the same amount of fabric around the button.
Step 24: Put the edges of the fabric into the button.
If the fabric looks bulky, don't worry.You'll need to hold the fabric in place with your finger.
Step 25: The button should be placed on top of the fabric.
There are two types of backs for button cover kits, a smooth back and a back with a shank.The back should be smooth.If your button kit only came with the backings, you should use a pair of needle nose pliers.
Step 26: The other part of the button maker can be used to assemble your button.
Take the plastic part of your button maker.Make sure the fabric is tucked under it by pressing it on top of the button backing.Push it down hard.As the button comes together, you should feel a slight "thump".Try hitting the plastic part with a hammer or mallet if you don't feel the thump.
Step 27: Attach the earring post to the button.
Place a large amount of glue on the front of a blank earring post, then press the post against the back of the button.If glue leaks out, don't worry.
Step 28: Wait for the earring to dry before making a second one.
They are ready to wear once the earrings are dry.