A tattoo machine is a hand-held device that is used to create permanent tattoos.Handling a tattoo gun can seem daunting as it takes intense focus and a steady hand, but it can be magical.An emphasis on hygiene is a must for the artist and the tattoo gun.
Step 1: Do not touch the equipment with your hands.
You are the most likely place to find major germs.Put on anti-bacterial soap and wash your body thoroughly.You should scrub your hands for at least 20 seconds.
Step 2: Brand new supplies are good for use.
New needles, gloves, and ink caps are some of the things tattoo parlors will use.Almost everything is thrown away after use.Each set of needles and tubes is individually packaged.The work space stays clean and no one is sharing needles.
Step 3: You can clean your instruments with an autoclave.
A combination of steam, heat and pressure is used in autoclaves.The equipment takes about twenty minutes to clean.Once the process is over, the door opens to let the contents cool and dry.The most reliable system for sterilizing equipment is the autoclave.
Step 4: The pieces of the tattoo gun should be arranged.
The contact screw and the front spring are on the machine.The line you are tattooing is determined by the distance between the two points.Put the needle in the tube and insert it into the slot.Once the tube is in the slot, the wing nut should be tightened.You should inspect the equipment as you put it together.If you see equipment that is in bad shape, throw it away and replace it.Bleeding and scarring can be caused by dull needles.
Step 5: The length of the needle can be set.
The distance from the tip of the tube to the needle is the correct length.Put the needle in place with the help of two screws.When you put the bar in, make sure the eye loop of the needle is turned to the left.This makes sure the needle is inserted correctly.It could lead to a painful skin piercing if it is not correct.
Step 6: Set the equipment out on your desk.
There is an easy-to-reach place for your supplies.Rub alcohol and cotton balls with rubber gloves.You can prevent any problems that might arise by having these tools at your disposal.It's always better to have more than you need, so keep extra gloves and cotton balls handy.
Step 7: The power source needs to be plugged in.
You can get a power supply with a display.The right voltage is usually between 1.5 and 18.You need a clip cord and a footswitch.The cord connects the power supply to the machine and the footswitch allows you to control the speed of the needle.These items are not as expensive as a tattoo machine kit.
Step 8: Put the ink in the gun.
If you want to put less ink than you need, focus on doing a clean pour.You don't want your tattoo machine to have too much ink.To get the ball rolling quickly, try to add only enough ink.
Step 9: The design can be put on the person's skin.
To make sure the design sticks to the skin, use specialized paper and stencil liquid.The stencil liquid spread over the area that is about to be tattooed is the reason for it.The outline is there for a reason.Staying close to the lines will help you create the best tattoo you can.
Step 10: Push the needle into the person.
It's not necessary to push the needle too hard.Scales back on how deep the needle goes through the skin if you see blood.Pull the needle out of the person's skin if it doesn't resist.It is possible to determine if you are using the needle correctly by working on a melon.You are pushing the needle too deep if the fruit is damaged.
Step 11: The design should be outlined.
Move the needle down the stencil line once it is in a comfortable position.To avoid injuries, move the needle slowly.Make sure the machine is above your hand by keeping a firm grip on the needle tube.Maintaining a strong grip is important when using a tattoo gun.Hold the needle tube in the same way you would a pencil.
Step 12: The person has excess ink on their skin.
There will be a lot of ink after the tattoo is done.Don't put any lotion on the tattoo, clean it as fast as you can.This can cause skin problems.Cleaning the ink is the most important thing to do after the tattoo is done.Allow the tattoo to sit for a while so the inflammation doesn't get worse.Once the ink has settled, apply a small amount of ointment and cover the tattoo with a bandage to protect it during the healing process.