The most common cause of a Whirlpool washer door being locked and not being able to open is a faulty lid switch (including the striker). The door switch locks and unlocks your door depending on which stage your wash cycle is at. Unplug the power to the washer. Locate the lid switch (consult your manual if necessary).Jun 7, 2021
How do I get my washer out of Control Lock?
- Press and hold the LOCK button for 3 seconds.
- A sound is made to indicate the lock/unlock status. The control lock icon on the display will light up when the feature is on.
Why is my washer stuck on lock?
The most common cause is water left in the machine. Try running a spin/drain cycle. If this fails, the machine can be drained by placing the washing machine drain hose lower than the drum (into a bucket or tray). The door interlock has simply jammed.
How do you reset a locked Whirlpool washer?
Unplug your Whirlpool washer and leave it unplugged for 45 minutes. After 45 minutes, plug your washer back in. The washer's programming should be reset and the door should open.
How do you reset a locked washing machine?
To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.
How do I turn off the control lock on my GE washer?
https://www.youtube.com/watch?v=CFTZRm1xiu4
How do you reset the door lock on a Whirlpool washing machine?
You should be able to hear an unlatching sound followed by being able to open the door. If that didn't work, the next step is to press down the “end of cycle” button (if your specific washer has one) for a few seconds this will manually reset the washer, and the door should be able to be opened.Jun 7, 2021
Why is my washer stuck on control lock?
Select and hold END OF CYCLE SIGNAL for 3 seconds until the CONTROL LOCKED Status light turns off. If that does not do it, try putting the machine into diagnostic mode. The washer must be empty and the control must be in the OFF state before pressing the touch-pad sequence to start the test. Close the door.Nov 2, 2012
Why is my washer saying locked?
The Control Lock feature on Front Load Washers can prevent any selections from being made when activated. The controls can be locked or unlocked after a cycle has started. Children cannot accidentally start the washer by touching pads with this option selected.
How do you reset the control lock on a Whirlpool washer?
- Locate the "Control Lock/Unlock" button on your Duet's control panel.
- Press and hold the "Control Lock/Unlock" button for three seconds.
- Release the "Control Lock/Unlock" button when the control lock icon on the display disappears.
How do I get my washing machine to unlock?
https://www.youtube.com/watch?v=J7vzWGMvfOM
How do I reset my Whirlpool front loader door lock?
- Unplug the washer from its wall outlet and leave the machine unplugged for about 2 minutes.
- Go ahead and plug the washer back in after 2 minutes.
How do I reset my GE washercontrol board?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
Where is the reset button on a Whirlpool washer?
https://www.youtube.com/watch?v=fIVa7YE-xdc
How do I turn off the lock on my Whirlpool washing machine?
Press the button for that dedicated key to activate and deactivate the Control Lock. To turn off Control Lock, press and hold the Options key that says "Control Lock Hold 3 Sec" under it for 3 seconds.
How do I reset my Whirlpool front load washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I unlock my Whirlpool washer Loc?
If you do not see the 3-2-1 countdown and are unable to de-activate Control Lock, try pressing the POWER button first, then touch and hold 3 seconds to de-activate control lock. If this does not work, try unplugging the machine or turning off the breaker for 1 minute, then power the machine back on and try again.
How do I get my Whirlpool washer to unlock?
Press the “Drain and Spin” button on the washer's control panel to attempt to unlock the machine. This may drain any excess water that could cause the machine to remain locked. Once the “Drain and Spin” cycle completes, the door should unlock.
How do you unlock my washer if it is locked?
Opening a Manual Lock. Turn the washing machine off and unplug it. If you're in the middle of a cycle, turn the dial or press the button to pause or end the cycle. Wait 5-6 seconds to see if the door unlocks.
How do I unlock my Whirlpool washer?
Hold down the "Control Lock" button on your Whirlpool washer for three seconds at the end of the washing cycle. Listen, and when you hear the unlatching sound, the door should open.
How do you manually unlock a GE washing machine?
If the washer is running, press the START/PAUSE button once it will pause the washer and unlock the door. It will take a few seconds for the door to unlock after pressing PAUSE. Press again to restart the wash cycle. In some cycles the washer will drain first, and then unlock the door when it is paused.